How to Make a Chainsaw Winch? – [Step by Step Guide]

Redisposing huge objects from one place to another is a near-impossible task. A homemade portable winch can be of great assistance to haul whatever load you need. Rather than spending a fortune on a chainsaw winch from the local hardware store, make it a cost-effective and doable project. A chainsaw motor powers this universal machine.

How to Make a Chainsaw Winch – Steps

There is a full method and step-by-step guide to building a chainsaw winch below.

Step 1: Remove the chainsaw

The first thing you need to do is separate the chainsaw from the engine. Without doing so, the making process will not start. That is because the saw and the winch cannot be in one engine at once.

 In case you don’t know how to disassemble, you can read the instructions. You can also use this guide when you want to reconnect. Store the saw in a safe place once you’ve separated it. When cutting down trees, this saw comes in handy.

Step 2: Check your chainsaw’s engine

An inefficient chainsaw engine cannot be able to work as a winch. In addition to checking the engine, you should do the main work as well. Make sure all the parts of the engine work including the clutch and throttle. If any parts look rusty, you should stay away from the engine. An optimal clutch and throttle are essential in order to build a standard winch. Occasionally, you will need to change the oil. You get outstanding winching performance when the engine is well maintained.

Step 3: You need to make these changes

You already have a chainsaw, a chainsaw engine, and duct tape, for the most part. However, these ingredients alone are no longer sufficient. Other ingredients are also needed to create a homemade winch. For example, scrap metals and cables may be necessary.

Building a capstan requires using reliable, strong, and flexible steel cable. You might consider using aluminum as well. In addition to being rust-resistant, steel cables are solid enough not to break when used for heavy lifting.

Also, don’t forget to buy the basic parts the winch needs, such as a channel, a flat iron, a pulley, a shaft, an angle, and more.

What is the process of getting them?

The steel can be obtained from any local shop or steel supply house. It is also possible to obtain these parts from old wagons, but new ones will continue to provide better service.

Step 4: Set up the winch

Due to the fact that all parts are ready, you can assemble the chainsaw winch now. Just connect the steel cable. A capstan winch consists of winding a cable around a capstan. Build the base of the winch by cutting the flat iron, the channel, and the angles.

Step 5: The winch should be connected

All parts of the chainsaw must be removed after removing the saw. Remove the large washer from the joiner after removing the saw. You should also include a small washer to connect the winch. Now you can install the sprocket in the winch’s complementary hole. Here’s the front side, you’ll find two slots for putting the bar studs in.

As you turn to the lower side, you will see more slots and adjustable planks. These make a winch, simply fasten them.

Step 6: Enrol  the Cable

Enrollment in cable is the next step. Always try to keep it straight because a tangled or wrinkled cable will not look good. Now, drop through the hole. It should be placed on the drum and pushed through to the other side.

In this case, duct tape can be used as a solution to stop rolling around the cable. The tape keeps cable from spooling automatically, so sometimes it helps to hold it in place.

Step 7: Finishing Touch

It’s time to start the engine with your new homemade winch. The cable has to be unrolled so you can lock the winch. Please remember that the chainsaw doesn’t need to be attached to the winch. Make sure the load is secure. Avoid loading the winch with loads exceeding 5000 pounds.

What is a chainsaw winch?

The chainsaw winch is a handy multi-purpose winching device that uses a chainsaw motor to lift heavy goods – simply remove the bar (which goes without saying) and use your chainsaw powerhead.

It has a lengthy cable that is looped around a drum multiple times. It boasts a robust but lightweight construction that makes it easy to transport in any car’s boot. Some winches are built to secure the vehicle’s front bumper, while others are attached to the frame.

You can secure the chainsaw winch to the bed of your truck with appropriate adapters if you wish to boost the unit’s safety. Some adapters function by fastening the unit to a rock, while others work by fitting the trailer hitch. The adapters keep the winch from shifting while it’s being used. As a result, adapters assure your safety as well as the safety of the saw and whatever you’re transporting.

How do you get a chainsaw winch?

Though seldom used on a daily basis, a chainsaw winch is necessary for lifting hefty loads, especially when logging or hunting. This equipment is a forestry winching device that can be used for a variety of tasks. It makes hauling the load upward much easier.

To get a chainsaw winch you are left with mainly two options, either you buy it from the store, or you make it at your own home. Now because this article is titled – How to make a chainsaw winch, what we are going to do is enrich you with some very useful DIY methods for making your own chainsaw winch! Also, buying a hulking winch is more expensive than building it (yet we are going to cover that too).

Chainsaw winches in the market

The three best chainsaw winches you’ll find available on Amazon/EBay are:

  1. The Honda GHX-50 gas-powered winch
  2. Lewis Chainsaw Winch 400 MK2
  3. Streamline Industrial Chainsaw Winch

Leave a Comment